| Author |
Message |
|
dirty birdy
Joined: Tue Feb 03, 2009 3:00 am
Posts: 2710
Location: Area 51
|
 What the...?  db
|
| Tue Oct 25, 2011 7:16 am |
|
|
|
The Machinist
Joined: Fri Jan 09, 2009 7:43 pm
Posts: 1601
Location: Eugene, Oregon
|
Re: What the...? Isometric view and a scale reference please.
|
| Tue Oct 25, 2011 7:45 am |
|
|
|
dirty birdy
Joined: Tue Feb 03, 2009 3:00 am
Posts: 2710
Location: Area 51
|
Re: What the...? The Machinist wrote: Isometric view and a scale reference please. Here's an isometric view, including a reference plane, along with a scale reference. Additional views and references put on hold until camera is nearby.   db
|
| Tue Oct 25, 2011 8:16 am |
|
|
|
dirty birdy
Joined: Tue Feb 03, 2009 3:00 am
Posts: 2710
Location: Area 51
|
Re: What the...? Details emerge slowly...   Critical parameters.... Diameter 41mm : Width 64mm : Mass....297 grams! db
|
| Tue Oct 25, 2011 5:16 pm |
|
|
|
vguitars
Joined: Thu Jan 08, 2009 2:05 pm
Posts: 2971
Location: Cleveland
|
Re: What the...? so its a lightweight 
|
| Tue Oct 25, 2011 7:28 pm |
|
|
|
The Machinist
Joined: Fri Jan 09, 2009 7:43 pm
Posts: 1601
Location: Eugene, Oregon
|
Re: What the...? Is the shaft diameter 3/8 or 10mm?
|
| Tue Oct 25, 2011 10:03 pm |
|
|
|
Spartanik
Joined: Tue Dec 07, 2010 1:29 am
Posts: 30
Location: Germany
|
Re: What the...?  It must be dead-unresponsive beefcaked like that! Hey, and I like the fact that there are a few possibilities to tune out the vibs...
|
| Wed Oct 26, 2011 12:15 am |
|
|
|
dirty birdy
Joined: Tue Feb 03, 2009 3:00 am
Posts: 2710
Location: Area 51
|
Re: What the...? The Machinist wrote: Is the shaft diameter 3/8 or 10mm? 3/8"
|
| Wed Oct 26, 2011 6:35 am |
|
|
|
The Machinist
Joined: Fri Jan 09, 2009 7:43 pm
Posts: 1601
Location: Eugene, Oregon
|
Re: What the...? uncle.
|
| Wed Oct 26, 2011 7:34 am |
|
|
|
dirty birdy
Joined: Tue Feb 03, 2009 3:00 am
Posts: 2710
Location: Area 51
|
Re: What the...? The Machinist wrote: uncle. I guess you're going to have to wait with the rest of the folks!  It's integral to a soon to be published technobabble thread I'm trying to complete in my infinite spare time.  db P.S. I believe I know where you were heading with this, and some of your thoughts were probably correct, but the rest, unfortunately, became mired in the depths of overthinking... 
|
| Wed Oct 26, 2011 7:48 am |
|
|
|
The Machinist
Joined: Fri Jan 09, 2009 7:43 pm
Posts: 1601
Location: Eugene, Oregon
|
Re: What the...? I believe you are correct about the overthinking part.
|
| Wed Oct 26, 2011 8:06 am |
|
|
